LLDP-EXT-DOT1-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Integer32 FROM SNMPv2-SMI TruthValue FROM SNMPv2-TC SnmpAdminString FROM SNMP-FRAMEWORK-MIB MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF lldpExtensions, lldpLocPortNum, lldpRemTimeMark, lldpRemLocalPortNum, lldpRemIndex, lldpPortConfigEntry FROM LLDP-MIB VlanId FROM Q-BRIDGE-MIB; lldpXdot1MIB MODULE-IDENTITY LAST-UPDATED "200404190000Z" -- April 19, 2004 ORGANIZATION "IEEE 802.1AB Working Group" CONTACT-INFO " WG-URL: http://grouper.ieee.org/groups/802/1/index.html WG-EMail: stds-802-1@ieee.org Contact: Paul Congdon Postal: Hewlett-Packard Company 8000 Foothills Blvd. Roseville, CA 95747 USA Tel: +1-916-785-5753 E-mail: paul_congdon@hp.com" DESCRIPTION "The LLDP Management Information Base extension module for IEEE 802.3 organizationally defined discovery information. In order to assure the uniqueness of the LLDP-MIB, lldpXdot1MIB is branched from lldpExtensions using OUI value as the node. An OUI/'company_id' is a 24 bit globally unique assigned number referenced by various standards. Copyright (C) IEEE 801.1AB Working Group (2004). This version of this MIB module is published as Clause 12 of IEEE Std. 802.1AB-2004; see the standard itself for full legal notices." REVISION "200404190000Z" -- April 19, 2004 DESCRIPTION "Published as part of IEEE Std. 802.1AB-2004 initial version." ::= { lldpExtensions YYYYYY } ------------------------------------------------------------------------------ ------------------------------------------------------------------------------ -- -- Organizationally Defined Information Extension - IEEE 802.1 -- ------------------------------------------------------------------------------ ------------------------------------------------------------------------------ lldpXdot1Objects OBJECT IDENTIFIER ::= { lldpXdot1MIB 1 } -- LLDP IEEE 802.1 extension MIB groups lldpXdot1Config OBJECT IDENTIFIER ::= { lldpXdot1Objects 1 } lldpXdot1LocalData OBJECT IDENTIFIER ::= { lldpXdot1Objects 2 } lldpXdot1RemoteData OBJECT IDENTIFIER ::= { lldpXdot1Objects 3 } ------------------------------------------------------------------------------ -- IEEE 802.1 - Configuration ------------------------------------------------------------------------------ -- -- lldpXdot1ConfigPortVlanTable : configure the transmission of the -- Port VLAN-ID TLVs on set of ports. -- lldpXdot1ConfigPortVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF LldpXdot1ConfigPortVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that controls selection of LLDP Port VLAN-ID TLVs to be transmitted on individual ports." ::= { lldpXdot1Config 1 } lldpXdot1ConfigPortVlanEntry OBJECT-TYPE SYNTAX LldpXdot1ConfigPortVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "LLDP configuration information that controls the transmission of IEEE 802.1 organizationally defined Port VLAN-ID TLV on LLDP transmission capable ports. This configuration object augments the lldpPortConfigEntry of the LLDP-MIB, therefore it is only present along with the port configuration defined by the associated lldpPortConfigEntry entry. Each active lldpConfigEntry must be restored from non-volatile storage (along with the corresponding lldpPortConfigEntry) after a re-initialization of the management system." AUGMENTS { lldpPortConfigEntry } ::= { lldpXdot1ConfigPortVlanTable 1 } LldpXdot1ConfigPortVlanEntry ::= SEQUENCE { lldpXdot1ConfigPortVlanTxEnable TruthValue } lldpXdot1ConfigPortVlanTxEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "The lldpXdot1ConfigPortVlanTxEnable, which is defined as a truth value and configured by the network management, determines whether the IEEE 802.1 organizationally defined port VLAN TLV transmission is allowed on a given LLDP transmission capable port. The default value for lldpXdot1ConfigPortVlanTxEnable object is 'false(2)'. The value of this object must be restored from non-volatile storage after a re-initialization of the management system." REFERENCE "IEEE 802.1AB-2004 section 10.2.1.1" DEFVAL { false } ::= { lldpXdot1ConfigPortVlanEntry 1 } -- -- lldpXdot1ConfigVlanNameTable : configure the transmission of the -- VLAN name instances on set of ports. -- lldpXdot1ConfigVlanNameTable OBJECT-TYPE SYNTAX SEQUENCE OF LldpXdot1ConfigVlanNameEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table that controls selection of LLDP VLAN name TLV instances to be transmitted on individual ports." ::= { lldpXdot1Config 2 } lldpXdot1ConfigVlanNameEntry OBJECT-TYPE SYNTAX LldpXdot1ConfigVlanNameEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "LLDP configuration information that specifies the set of ports (represented as a PortList) on which the Local System VLAN name instance will be transmitted. This configuration object augments the lldpLocVlanEntry, therefore it is only present along with the VLAN Name instance contained in the associated lldpLocVlanNameEntry entry. Each active lldpXdot1ConfigVlanNameEntry must be restored from non-volatile storage (along with the corresponding lldpXdot1LocVlanNameEntry) after a re-initialization of the management system." AUGMENTS { lldpXdot1LocVlanNameEntry } ::= { lldpXdot1ConfigVlanNameTable 1 } LldpXdot1ConfigVlanNameEntry ::= SEQUENCE { lldpXdot1ConfigVlanNameTxEnable TruthValue } lldpXdot1ConfigVlanNameTxEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "The boolean value that indicates whether the corresponding Local System VLAN name instance will be transmitted on the port defined by the given lldpXdot1LocVlanNameEntry. The default value for lldpXdot1ConfigVlanNameTxEnable object is 'false(2)'. The value of this object must be restored from non-volatile storage after a re-initialization of the management system." REFERENCE "IEEE 802.1AB-2004 section 10.2.1.1" DEFVAL { false } ::= { lldpXdot1ConfigVlanNameEntry 1 } -- -- lldpXdot1ConfigProtoVlanTable : configure the transmission of the -- protocol VLAN instances on set -- of ports. -- lldpXdot1ConfigProtoVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF LldpXdot1ConfigProtoVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table that controls selection of LLDP Protocol VLAN TLV instances to be transmitted on individual ports." ::= { lldpXdot1Config 3 } lldpXdot1ConfigProtoVlanEntry OBJECT-TYPE SYNTAX LldpXdot1ConfigProtoVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "LLDP configuration information that specifies the set of ports (represented as a PortList) on which the Local System Protocol VLAN instance will be transmitted. This configuration object augments the lldpXdot1LocVlanEntry, therefore it is only present along with the Protocol VLAN instance contained in the associated lldpXdot1LocVlanEntry entry. Each active lldpXdot1ConfigProtoVlanEntry must be restored from non-volatile storage (along with the corresponding lldpXdot1LocProtoVlanEntry) after a re-initialization of the management system." AUGMENTS { lldpXdot1LocProtoVlanEntry } ::= { lldpXdot1ConfigProtoVlanTable 1 } LldpXdot1ConfigProtoVlanEntry ::= SEQUENCE { lldpXdot1ConfigProtoVlanTxEnable TruthValue } lldpXdot1ConfigProtoVlanTxEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "The boolean value that indicates whether the corresponding Local System Port and Protocol VLAN instance will be transmitted on the port defined by the given lldpXdot1LocProtoVlanEntry. The default value for lldpXdot1ConfigVlanNameTxEnable object is 'false(2)'. The value of this object must be restored from non-volatile storage after a re-initialization of the management system." REFERENCE "IEEE 802.1AB-2004 section 10.2.1.1" DEFVAL { false } ::= { lldpXdot1ConfigProtoVlanEntry 1 } -- -- lldpXdot1ConfigProtocolTable : configure the transmission of the -- protocol instances on set -- of ports. -- lldpXdot1ConfigProtocolTable OBJECT-TYPE SYNTAX SEQUENCE OF LldpXdot1ConfigProtocolEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table that controls selection of LLDP Protocol TLV instances to be transmitted on individual ports." ::= { lldpXdot1Config 4 } lldpXdot1ConfigProtocolEntry OBJECT-TYPE SYNTAX LldpXdot1ConfigProtocolEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "LLDP configuration information that specifies the set of ports (represented as a PortList) on which the Local System Protocol instance will be transmitted. This configuration object augments the lldpXdot1LocProtoEntry, therefore it is only present along with the Protocol instance contained in the associated lldpXdot1LocProtoEntry entry. Each active lldpXdot1ConfigProtocolEntry must be restored from non-volatile storage (along with the corresponding lldpXdot1LocProtocolEntry) after a re-initialization of the management system." AUGMENTS { lldpXdot1LocProtocolEntry } ::= { lldpXdot1ConfigProtocolTable 1 } LldpXdot1ConfigProtocolEntry ::= SEQUENCE { lldpXdot1ConfigProtocolTxEnable TruthValue } lldpXdot1ConfigProtocolTxEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "The boolean value that indicates whether the corresponding Local System Protocol Identity instance will be transmitted on the port defined by the given lldpXdot1LocProtocolEntry. The default value for lldpXdot1ConfigProtocolTxEnable object is 'false(2)'. The value of this object must be restored from non-volatile storage after a re-initialization of the management system." REFERENCE "IEEE 802.1AB-2004 section 10.2.1.1" DEFVAL { false } ::= { lldpXdot1ConfigProtocolEntry 1 } ------------------------------------------------------------------------------ -- IEEE 802.1 - Local System Information ------------------------------------------------------------------------------ lldpXdot1LocTable OBJECT-TYPE SYNTAX SEQUENCE OF LldpXdot1LocEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains one row per port for IEEE 802.1 organizationally defined LLDP extension on the local system known to this agent." ::= { lldpXdot1LocalData 1 } lldpXdot1LocEntry OBJECT-TYPE SYNTAX LldpXdot1LocEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about IEEE 802.1 organizationally defined LLDP extension." INDEX { lldpLocPortNum } ::= { lldpXdot1LocTable 1 } LldpXdot1LocEntry ::= SEQUENCE { lldpXdot1LocPortVlanId Integer32 } lldpXdot1LocPortVlanId OBJECT-TYPE SYNTAX Integer32(0|1..4094) MAX-ACCESS read-only STATUS current DESCRIPTION "The integer value used to identify the port's VLAN identifier associated with the local system. A value of zero shall be used if the system either does not know the PVID or does not support port-based VLAN operation." REFERENCE "IEEE 802.1AB-2004 section F.2.1" ::= { lldpXdot1LocEntry 1 } -- -- lldpXdot1LocProtoVlanTable: Port and Protocol VLAN information -- lldpXdot1LocProtoVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF LldpXdot1LocProtoVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains one or more rows per Port and Protocol VLAN information about the local system." ::= { lldpXdot1LocalData 2 } lldpXdot1LocProtoVlanEntry OBJECT-TYPE SYNTAX LldpXdot1LocProtoVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Port and protocol VLAN name Information about a particular port component. There may be multiple protocol VLANs, identified by a particular lldpXdot1LocProtoVlanId, configured on the given port." INDEX { lldpLocPortNum, lldpXdot1LocProtoVlanId } ::= { lldpXdot1LocProtoVlanTable 1 } LldpXdot1LocProtoVlanEntry ::= SEQUENCE { lldpXdot1LocProtoVlanId Integer32, lldpXdot1LocProtoVlanSupported TruthValue, lldpXdot1LocProtoVlanEnabled TruthValue } lldpXdot1LocProtoVlanId OBJECT-TYPE SYNTAX Integer32(0|1..4094) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The integer value used to identify the port and protocol VLANs associated with the given port associated with the local system. A value of zero shall be used if the system either does not know the protocol VLAN ID (PPVID) or does not support port and protocol VLAN operation." REFERENCE "IEEE 802.1AB-2004 section F.3.2" ::= { lldpXdot1LocProtoVlanEntry 1 } lldpXdot1LocProtoVlanSupported OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "The truth value used to indicate whether the given port (associated with the local system) supports port and protocol VLANs." REFERENCE "IEEE 802.1AB-2004 section F.3.1" ::= { lldpXdot1LocProtoVlanEntry 2 } lldpXdot1LocProtoVlanEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "The truth value used to indicate whether the port and protocol VLANs are enabled on the given port associated with the local system." REFERENCE "IEEE 802.1AB-2004 section F.3.1" ::= { lldpXdot1LocProtoVlanEntry 3 } -- -- lldpXdot1LocVlanNameTable : VLAN name information about the local system -- lldpXdot1LocVlanNameTable OBJECT-TYPE SYNTAX SEQUENCE OF LldpXdot1LocVlanNameEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains one or more rows per IEEE 802.1Q VLAN name information on the local system known to this agent." ::= { lldpXdot1LocalData 3 } lldpXdot1LocVlanNameEntry OBJECT-TYPE SYNTAX LldpXdot1LocVlanNameEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "VLAN name Information about a particular port component. There may be multiple VLANs, identified by a particular lldpXdot1LocVlanNameId, configured on the given port." INDEX { lldpLocPortNum, lldpXdot1LocVlanNameId } ::= { lldpXdot1LocVlanNameTable 1 } LldpXdot1LocVlanNameEntry ::= SEQUENCE { lldpXdot1LocVlanNameId VlanId, lldpXdot1LocVlanName SnmpAdminString } lldpXdot1LocVlanNameId OBJECT-TYPE SYNTAX VlanId MAX-ACCESS not-accessible STATUS current DESCRIPTION "The integer value used to identify the IEEE 802.1Q VLAN IDs with which the given port is compatible." REFERENCE "IEEE 802.1AB-2004 section F.4.2" ::= { lldpXdot1LocVlanNameEntry 1 } lldpXdot1LocVlanName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(1..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The string value used to identify VLAN name identified by the VLANs associated with the given port associated with the local system. This object should contain the value of the dot1QVLANStaticName object (defined in IETF RFC 2674) identified with the given lldpXdot1LocVlanId." REFERENCE "IEEE 802.1AB-2004 section F.4.4" ::= { lldpXdot1LocVlanNameEntry 2 } -- -- lldpXdot1LocProtocolTable : Protocol Identity information -- lldpXdot1LocProtocolTable OBJECT-TYPE SYNTAX SEQUENCE OF LldpXdot1LocProtocolEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains one or more rows per protocol identity information on the local system known to this agent." REFERENCE "IEEE 802.1AB-2004 section F.5" ::= { lldpXdot1LocalData 4 } lldpXdot1LocProtocolEntry OBJECT-TYPE SYNTAX LldpXdot1LocProtocolEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about particular protocols that are accessible through the given port component. There may be multiple protocols, identified by particular lldpXdot1ProtocolIndex, and lldpLocPortNum." REFERENCE "IEEE 802.1AB-2004 section F.5" INDEX { lldpLocPortNum, lldpXdot1LocProtocolIndex } ::= { lldpXdot1LocProtocolTable 1 } LldpXdot1LocProtocolEntry ::= SEQUENCE { lldpXdot1LocProtocolIndex Integer32, lldpXdot1LocProtocolId OCTET STRING } lldpXdot1LocProtocolIndex OBJECT-TYPE SYNTAX Integer32(1..2147483647) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object represents an arbitrary local integer value used by this agent to identify a particular protocol identity." ::= { lldpXdot1LocProtocolEntry 1 } lldpXdot1LocProtocolId OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "The octet string value used to identify the protocols associated with the given port of the local system." REFERENCE "IEEE 802.1AB-2004 section F.5.1" ::= { lldpXdot1LocProtocolEntry 2 } ------------------------------------------------------------------------------ -- IEEE 802.1 - Remote System Information ------------------------------------------------------------------------------ lldpXdot1RemTable OBJECT-TYPE SYNTAX SEQUENCE OF LldpXdot1RemEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains one or more rows per physical network connection known to this agent. The agent may wish to ensure that only one lldpXdot1RemEntry is present for each local port, or it may choose to maintain multiple lldpXdot1RemEntries for the same local port." ::= { lldpXdot1RemoteData 1 } lldpXdot1RemEntry OBJECT-TYPE SYNTAX LldpXdot1RemEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a particular port component." INDEX { lldpRemTimeMark, lldpRemLocalPortNum, lldpRemIndex } ::= { lldpXdot1RemTable 1 } LldpXdot1RemEntry ::= SEQUENCE { lldpXdot1RemPortVlanId Integer32 } lldpXdot1RemPortVlanId OBJECT-TYPE SYNTAX Integer32(0|1..4094) MAX-ACCESS read-only STATUS current DESCRIPTION "The integer value used to identify the port's VLAN identifier associated with the remote system. if the remote system either does not know the PVID or does not support port-based VLAN operation, the value of lldpXdot1RemPortVlanId should be zero." REFERENCE "IEEE 802.1AB-2004 section F.2.1" ::= { lldpXdot1RemEntry 1 } lldpXdot1RemProtoVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF LldpXdot1RemProtoVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains one or more rows per Port and Protocol VLAN information about the remote system, received on the given port." ::= { lldpXdot1RemoteData 2 } lldpXdot1RemProtoVlanEntry OBJECT-TYPE SYNTAX LldpXdot1RemProtoVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Port and protocol VLAN name Information about a particular port component. There may be multiple protocol VLANs, identified by a particular lldpXdot1RemProtoVlanId, configured on the remote system." INDEX { lldpRemTimeMark, lldpRemLocalPortNum, lldpRemIndex, lldpXdot1RemProtoVlanId } ::= { lldpXdot1RemProtoVlanTable 1 } LldpXdot1RemProtoVlanEntry ::= SEQUENCE { lldpXdot1RemProtoVlanId Integer32, lldpXdot1RemProtoVlanSupported TruthValue, lldpXdot1RemProtoVlanEnabled TruthValue } lldpXdot1RemProtoVlanId OBJECT-TYPE SYNTAX Integer32(0|1..4094) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The integer value used to identify the port and protocol VLANs associated with the given port associated with the remote system. If port and protocol VLANs are not supported on the given port associated with the remote system, or if the port is not enabled with any port and protocol VLAN, the value of lldpXdot1RemProtoVlanId should be zero." REFERENCE "IEEE 802.1AB-2004 section F.3.2" ::= { lldpXdot1RemProtoVlanEntry 1 } lldpXdot1RemProtoVlanSupported OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "The truth value used to indicate whether the given port (associated with the remote system) is capable of supporting port and protocol VLANs." REFERENCE "IEEE 802.1AB-2004 section F.3.1" ::= { lldpXdot1RemProtoVlanEntry 2 } lldpXdot1RemProtoVlanEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "The truth value used to indicate whether the port and protocol VLANs are enabled on the given port associated with the remote system." REFERENCE "IEEE 802.1AB-2004 section F.3.1" ::= { lldpXdot1RemProtoVlanEntry 3 } -- -- lldpXdot1RemVlanNameTable : VLAN name information of the remote -- systems -- lldpXdot1RemVlanNameTable OBJECT-TYPE SYNTAX SEQUENCE OF LldpXdot1RemVlanNameEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains one or more rows per IEEE 802.1Q VLAN name information about the remote system, received on the given port." REFERENCE "IEEE 802.1AB-2004 section F.4" ::= { lldpXdot1RemoteData 3 } lldpXdot1RemVlanNameEntry OBJECT-TYPE SYNTAX LldpXdot1RemVlanNameEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "VLAN name Information about a particular port component. There may be multiple VLANs, identified by a particular lldpXdot1RemVlanNameId, received on the given port." INDEX { lldpRemTimeMark, lldpRemLocalPortNum, lldpRemIndex, lldpXdot1RemVlanNameId } ::= { lldpXdot1RemVlanNameTable 1 } LldpXdot1RemVlanNameEntry ::= SEQUENCE { lldpXdot1RemVlanNameId VlanId, lldpXdot1RemVlanName SnmpAdminString } lldpXdot1RemVlanNameId OBJECT-TYPE SYNTAX VlanId MAX-ACCESS not-accessible STATUS current DESCRIPTION "The integer value used to identify the IEEE 802.1Q VLAN IDs with which the given port of the remote system is compatible." REFERENCE "IEEE 802.1AB-2004 section F.4.2" ::= { lldpXdot1RemVlanNameEntry 1 } lldpXdot1RemVlanName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(1..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The string value used to identify VLAN name identified by the VLAN Id associated with the remote system." REFERENCE "IEEE 802.1AB-2004 section F.4.4" ::= { lldpXdot1RemVlanNameEntry 2 } -- -- lldpXdot1RemProtocolTable : Protocol information of the remote systems -- lldpXdot1RemProtocolTable OBJECT-TYPE SYNTAX SEQUENCE OF LldpXdot1RemProtocolEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains one or more rows per protocol information about the remote system, received on the given port." ::= { lldpXdot1RemoteData 4 } lldpXdot1RemProtocolEntry OBJECT-TYPE SYNTAX LldpXdot1RemProtocolEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Protocol information about a particular port component. There may be multiple protocols, identified by a particular lldpXdot1ProtocolIndex, received on the given port." INDEX { lldpRemTimeMark, lldpRemLocalPortNum, lldpRemIndex, lldpXdot1RemProtocolIndex } ::= { lldpXdot1RemProtocolTable 1 } LldpXdot1RemProtocolEntry ::= SEQUENCE { lldpXdot1RemProtocolIndex Integer32, lldpXdot1RemProtocolId OCTET STRING } lldpXdot1RemProtocolIndex OBJECT-TYPE SYNTAX Integer32(1..2147483647) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object represents an arbitrary local integer value used by this agent to identify a particular protocol identity." ::= { lldpXdot1RemProtocolEntry 1 } lldpXdot1RemProtocolId OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "The octet string value used to identify the protocols associated with the given port of remote system." REFERENCE "IEEE 802.1AB-2004 section F.5.3" ::= { lldpXdot1RemProtocolEntry 2 } -- conformance information lldpXdot1Conformance OBJECT IDENTIFIER ::= { lldpXdot1MIB 2 } lldpXdot1Compliances OBJECT IDENTIFIER ::= { lldpXdot1Conformance 1 } lldpXdot1Groups OBJECT IDENTIFIER ::= { lldpXdot1Conformance 2 } -- compliance statements lldpXdot1Compliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for SNMP entities which implement the IEEE 802.1 organizationally defined LLDP extension MIB." MODULE -- this module MANDATORY-GROUPS { lldpXdot1ConfigGroup, lldpXdot1RemSysGroup } GROUP lldpXdot1OptLocSysGroup DESCRIPTION "This object represents the information associated with the IEEE 802.1 organizationally defined optional TLVs, therefore the agent may not implement them." ::= { lldpXdot1Compliances 1 } -- MIB groupings lldpXdot1ConfigGroup OBJECT-GROUP OBJECTS { lldpXdot1ConfigPortVlanTxEnable, lldpXdot1ConfigVlanNameTxEnable, lldpXdot1ConfigProtoVlanTxEnable, lldpXdot1ConfigProtocolTxEnable } STATUS current DESCRIPTION "The collection of objects which are used to configure the IEEE 802.1 organizationally defined LLDP extension implementation behavior. This group is mandatory for agents which implement the IEEE 802.1 organizationally defined LLDP extension." ::= { lldpXdot1Groups 1 } lldpXdot1OptLocSysGroup OBJECT-GROUP OBJECTS { lldpXdot1LocPortVlanId, lldpXdot1LocProtoVlanSupported, lldpXdot1LocProtoVlanEnabled, lldpXdot1LocVlanName, lldpXdot1LocProtocolId } STATUS current DESCRIPTION "The collection of objects which are used to represent IEEE 802.1 organizationally defined LLDP extension associated with the Local Device Information. This group is mandatory for agents which implement the IEEE 802.1 organizationally defined LLDP extension." ::= { lldpXdot1Groups 2 } lldpXdot1RemSysGroup OBJECT-GROUP OBJECTS { lldpXdot1RemPortVlanId, lldpXdot1RemProtoVlanSupported, lldpXdot1RemProtoVlanEnabled, lldpXdot1RemVlanName, lldpXdot1RemProtocolId } STATUS current DESCRIPTION "The collection of objects which are used to represent LLDP 802.1 organizational extension Local Device Information. This group is mandatory for agents which implement the LLDP 802.1 organizational extension." ::= { lldpXdot1Groups 3 } END