[Dime] [Editorial Errata Reported] RFC6733 (3997)

[RFC Errata System <[e-mail]>]

The following errata report has been submitted for RFC6733,
"Diameter Base Protocol".

--------------------------------------
You may review the report below and at:
http://www.rfc-editor.org/errata_search.php?rfc=6733&eid=3997

--------------------------------------
Type: Editorial
Reported by: Jouni Korhonen <[e-mail]>

Section: GLOBAL

Original Text
-------------
Section 2.1.

   The base Diameter protocol is run on port 3868 for both TCP [RFC0793]
   and SCTP [RFC4960].  For TLS [RFC5246] and Datagram Transport Layer
   Security (DTLS) [RFC6347], a Diameter node that initiates a
   connection prior to any message exchanges MUST run on port 5658.  It
   is assumed that TLS is run on top of TCP when it is used, and DTLS is
   run on top of SCTP when it is used.

   If the Diameter peer does not support receiving TLS/TCP and DTLS/SCTP
   connections on port 5658 (i.e., the peer complies only with RFC
   3588), then the initiator MAY revert to using TCP or SCTP on port
   3868.  Note that this scheme is kept only for the purpose of backward
   compatibility and that there are inherent security vulnerabilities
   when the initial CER/CEA messages are sent unprotected (see
   Section 5.6).

   Diameter clients MUST support either TCP or SCTP; agents and servers
   SHOULD support both.

   A Diameter node MAY initiate connections from a source port other
   than the one that it declares it accepts incoming connections on, and
   it MUST always be prepared to receive connections on port 3868 for
   TCP or SCTP and port 5658 for TLS/TCP and DTLS/SCTP connections.
   When DNS-based peer discovery (Section 5.2) is used, the port numbers
   received from SRV records take precedence over the default ports
   (3868 and 5658).

Section 4.3.1.

      port               = ":" 1*DIGIT

                      ; One of the ports used to listen for
                      ; incoming connections.
                      ; If absent, the default Diameter port
                      ; (3868) is assumed if no transport
                      ; security is used and port 5658 when
                      ; transport security (TLS/TCP and DTLS/SCTP)
                      ; is used.

Corrected Text
--------------
Section 2.1.

   The base Diameter protocol is run on port 3868 for both TCP [RFC0793]
   and SCTP [RFC4960].  For TLS [RFC5246] and Datagram Transport Layer
   Security (DTLS) [RFC6347], a Diameter node that initiates a
   connection prior to any message exchanges MUST run on port 5868.  It
   is assumed that TLS is run on top of TCP when it is used, and DTLS is
   run on top of SCTP when it is used.

   If the Diameter peer does not support receiving TLS/TCP and DTLS/SCTP
   connections on port 5868 (i.e., the peer complies only with RFC
   3588), then the initiator MAY revert to using TCP or SCTP on port
   3868.  Note that this scheme is kept only for the purpose of backward
   compatibility and that there are inherent security vulnerabilities
   when the initial CER/CEA messages are sent unprotected (see
   Section 5.6).

   Diameter clients MUST support either TCP or SCTP; agents and servers
   SHOULD support both.

   A Diameter node MAY initiate connections from a source port other
   than the one that it declares it accepts incoming connections on, and
   it MUST always be prepared to receive connections on port 3868 for
   TCP or SCTP and port 5868 for TLS/TCP and DTLS/SCTP connections.
   When DNS-based peer discovery (Section 5.2) is used, the port numbers
   received from SRV records take precedence over the default ports
   (3868 and 5868).

Section 4.3.1.

      port               = ":" 1*DIGIT

                      ; One of the ports used to listen for
                      ; incoming connections.
                      ; If absent, the default Diameter port
                      ; (3868) is assumed if no transport
                      ; security is used and port 5868 when
                      ; transport security (TLS/TCP and DTLS/SCTP)
                      ; is used.

Notes
-----
RFC 6733 defined the Diameter port number for secure transport in IANA considerations Section 11.4. to be 5868. This is also in IANA port numbers registry "Service Name and Transport Protocol Port Number Registry". However, the RFC 6733 body text uses different port number in Sections 2.1. and 4.3.1. for secure transports. Since the IANA registry already contains the port number 5868 instead of the body text used value 5658, the values in Sections 2.1. and 4.3.1. should be 5868 instead of 5658.

Instructions:
-------------
This errata is currently posted as "Reported". If necessary, please
use "Reply All" to discuss whether it should be verified or
rejected. When a decision is reached, the verifying party (IESG)
can log in to change the status and edit the report, if necessary. 

--------------------------------------
RFC6733 (draft-ietf-dime-rfc3588bis-33)
--------------------------------------
Title               : Diameter Base Protocol
Publication Date    : October 2012
Author(s)           : V. Fajardo, Ed., J. Arkko, J. Loughney, G. Zorn, Ed.
Category            : PROPOSED STANDARD
Source              : Diameter Maintenance and Extensions
Area                : Operations and Management
Stream              : IETF
Verifying Party     : IESG