X25MIB Part II
"Dean D. Throop" <throop@dg-rtp.dg.com> Fri, 12 June 1992 21:25 UTC
Received: from nri.reston.va.us by ietf.NRI.Reston.VA.US id aa14993; 12 Jun 92 17:25 EDT
Received: from nri.reston.va.us by NRI.Reston.VA.US id aa04678; 12 Jun 92 17:25 EDT
Received: from dg-rtp.rtp.dg.com by NRI.Reston.VA.US id aa04632; 12 Jun 92 17:24 EDT
Received: from walrus.rtp.dg.com by dg-rtp.dg.com (5.4/dg-rtp-proto) id AA16980; Fri, 12 Jun 1992 15:44:24 -0400
Received: by walrus (5.4.1/140.2) id AA03254; Fri, 12 Jun 1992 15:41:59 -0400
Date: Fri, 12 Jun 1992 15:41:59 -0400
From: "Dean D. Throop" <throop@dg-rtp.dg.com>
Message-Id: <9206121941.AA03254@walrus>
To: x25mib@dg-rtp
Subject: X25MIB Part II
-- ###########################################################
-- X.25 Channel Table
-- ###########################################################
x25ChannelTable OBJECT-TYPE
SYNTAX SEQUENCE OF X25ChannelEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"These objects contain information about the
channel number configuration in an X.25 PLE.
These values are the configured values.
changes in these values after the interfaces
has started may not be reflected in the
operating PLE."
REFERENCE "See ISO 8208, Section 3.7"
::= { x25 4 }
x25ChannelEntry OBJECT-TYPE
SYNTAX X25ChannelEntry
ACCESS not-accessible
STATUS mandatory
D. Throop Invalid after Dec 20, 92 [Page 38]
Internet Draft X.25 Packet Layer MIB June 1992
DESCRIPTION
"Entries of x25ChannelTable."
REFERENCE "This provides the information available
in 10733 logicalChannelAssignments."
INDEX { x25ChannelIndex }
::= { x25ChannelTable 1 }
X25ChannelEntry ::= SEQUENCE {
x25ChannelIndex
PositiveInteger,
x25ChannelLIC
INTEGER,
x25ChannelHIC
INTEGER,
x25ChannelLTC
INTEGER,
x25ChannelHTC
INTEGER,
x25ChannelLOC
INTEGER,
x25ChannelHOC
INTEGER
}
x25ChannelIndex OBJECT-TYPE
SYNTAX PositiveInteger
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A value that uniquely identifies the X.25
PLE subnetwork and matches its ifIndex
value. The values of this object can range
from one to ifNumber."
::= { x25ChannelEntry 1 }
x25ChannelLIC OBJECT-TYPE
SYNTAX INTEGER (0..4096)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Lowest Incoming channel."
::= { x25ChannelEntry 2 }
x25ChannelHIC OBJECT-TYPE
SYNTAX INTEGER (0..4096)
D. Throop Invalid after Dec 20, 92 [Page 39]
Internet Draft X.25 Packet Layer MIB June 1992
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Highest Incoming channel. A value of zero
indicates no channels in this range."
::= { x25ChannelEntry 3 }
x25ChannelLTC OBJECT-TYPE
SYNTAX INTEGER (0..4096)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Lowest Two-way channel."
::= { x25ChannelEntry 4 }
x25ChannelHTC OBJECT-TYPE
SYNTAX INTEGER (0..4096)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Highest Two-way channel. A value of zero
indicates no channels in this range."
::= { x25ChannelEntry 5 }
x25ChannelLOC OBJECT-TYPE
SYNTAX INTEGER (0..4096)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Lowest outgoing channel."
::= { x25ChannelEntry 6 }
x25ChannelHOC OBJECT-TYPE
SYNTAX INTEGER (0..4096)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Highest outgoing channel. A value of zero
indicates no channels in this range."
::= { x25ChannelEntry 7 }
-- ###########################################################
D. Throop Invalid after Dec 20, 92 [Page 40]
Internet Draft X.25 Packet Layer MIB June 1992
-- X25 Per Circuits Information Table
-- ###########################################################
x25CircuitTable OBJECT-TYPE
SYNTAX SEQUENCE OF X25CircuitEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"These objects contain general information
about a specific circuit of an X.25 PLE."
::= { x25 5 }
x25CircuitEntry OBJECT-TYPE
SYNTAX X25CircuitEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Entries of x25CircuitTable."
INDEX { x25CircuitIndex,
x25CircuitChannel }
::= { x25CircuitTable 1 }
X25CircuitEntry ::= SEQUENCE {
x25CircuitIndex
PositiveInteger,
x25CircuitChannel
INTEGER,
x25CircuitStatus
INTEGER,
x25CircuitEstablishTime
TimeTicks,
x25CircuitDirection
INTEGER,
x25CircuitInOctets
Counter,
x25CircuitInPdus
Counter,
x25CircuitInRemotelyInitiatedResets
Counter,
x25CircuitInProviderInitiatedResets
Counter,
x25CircuitInInterrupts
Counter,
x25CircuitOutOctets
Counter,
D. Throop Invalid after Dec 20, 92 [Page 41]
Internet Draft X.25 Packet Layer MIB June 1992
x25CircuitOutPdus
Counter,
x25CircuitOutInterrupts
Counter,
x25CircuitDataRetransmissionTimeouts
Counter,
x25CircuitResetTimeouts
Counter,
x25CircuitInterruptTimeouts
Counter,
x25CircuitCallParamId
OBJECT IDENTIFIER,
x25CircuitCalledDteAddress
X121Address,
x25CircuitCallingDteAddress
X121Address,
x25CircuitOriginallyCalledAddress
X121Address,
x25CircuitDescr
DisplayString
}
x25CircuitIndex OBJECT-TYPE
SYNTAX PositiveInteger
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A value that uniquely identifies the X.25
PLE subnetwork and matches its ifIndex
value. The values of this object can range
from one to ifNumber."
::= { x25CircuitEntry 1 }
x25CircuitChannel OBJECT-TYPE
SYNTAX INTEGER (1..4096)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The channel number for this circuit."
::= { x25CircuitEntry 2 }
x25CircuitStatus OBJECT-TYPE
SYNTAX INTEGER { -- state table states
invalid (1),
closed (2), -- (p1)
D. Throop Invalid after Dec 20, 92 [Page 42]
Internet Draft X.25 Packet Layer MIB June 1992
calling (3), -- (p2,p3,p5)
open (4), -- (p4)
clearing (5), -- (p6,p7)
pvc (6),
pvcResetting (7),
startClear (8), -- Close cmd
startPvcResetting (9), -- Reset cmd
other (10)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object reports the current status of
the circuit.
An existing instance of this object can only
be set to startClear, startPvcResetting, or
invalid. An instance with the value calling
or open can only be set to startClear and
that action will start clearing the circuit.
An instance with the value PVC can only be
set to startPvcResetting or invalid and that
action resets the PVC or deletes the circuit
respectively. The values startClear or
startPvcResetting will never be returned by
an agent. An attempt to set the status of
an existing instance to a value other than
one of these values will result in an error.
A non-existing instance can be set to PVC to
create a PVC if the implementation supports
dynamic creation of PVCs. Some
implementations may only allow creation and
deletion of PVCs if the interface is down.
Since the instance identifier will supply
the PLE index and the channel number,
setting this object alone supplies
sufficient information to create the
instance. All the DEFVAL clauses for the
other objects of this table are appropriate
for creating a PVC; PLEs creating entries
for placed or accepted calls will use values
appropriate for the call rather than the
value of the DEFVAL clause. Two managers
trying to create the same PVC can determine
D. Throop Invalid after Dec 20, 92 [Page 43]
Internet Draft X.25 Packet Layer MIB June 1992
from the return code which manager succeeded
and which failed (the failing manager fails
because it can not set a value of PVC for an
existing object).
An entry in the closed or invalid state may
be deleted or reused at the agent's
convence. If the entry is kept in the
closed state, the values of the parameters
associated with the entry must be correct.
Closed implies the values in the circuit
table are correct.
The value of invalid indicates the other
values in the table are invalid. Many
agents may never return a value of invalid
because they dynamically allocate and free
unused table entries. An agent for a
statically configured systems can return
invalid to indicate the entry has not yet
been used so the counters contain no
information."
REFERENCE "See ISO 8208,
table 33 for (p<n>) state table"
::= { x25CircuitEntry 3 }
x25CircuitEstablishTime OBJECT-TYPE
SYNTAX TimeTicks
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The value of sysUpTime when the channel was
associated with this circuit. For outgoing
SVCs, this is the time the first call packet
was sent. For incoming SVCs, this is the
time the call indication was received. For
PVCs this is the time the PVC was able to
pass data to a higher layer entity without
loss of data."
::= { x25CircuitEntry 4 }
x25CircuitDirection OBJECT-TYPE
SYNTAX INTEGER {
incoming (1),
outgoing (2),
D. Throop Invalid after Dec 20, 92 [Page 44]
Internet Draft X.25 Packet Layer MIB June 1992
pvc (3)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The direction of the call that established
this circuit."
REFERENCE "10733 direction"
DEFVAL { pvc }
::= { x25CircuitEntry 5 }
-- X25 Circuit data flow statistics
x25CircuitInOctets OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of octets of user data delivered
to upper layer."
REFERENCE "5.11 octetsReceivedCounter"
::= { x25CircuitEntry 6 }
x25CircuitInPdus OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of PDUs received for this
circuit."
REFERENCE "10733 5.11 dataPacketsReceived"
::= { x25CircuitEntry 7 }
x25CircuitInRemotelyInitiatedResets OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of Resets received for this
circuit with cause code of DTE initiated."
REFERENCE "10733 remotelyInitiatedResets"
::= { x25CircuitEntry 8 }
x25CircuitInProviderInitiatedResets OBJECT-TYPE
D. Throop Invalid after Dec 20, 92 [Page 45]
Internet Draft X.25 Packet Layer MIB June 1992
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of Resets received for this
circuit with cause code other than DTE
initiated."
REFERENCE "10733 ProviderInitiatedResets"
::= { x25CircuitEntry 9 }
x25CircuitInInterrupts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of interrupt packets received
for this circuit."
REFERENCE "10733 interruptPacketsReceived"
::= { x25CircuitEntry 10 }
x25CircuitOutOctets OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of octets of user data sent for
this circuit."
REFERENCE "10733 5.11 octetsSentCounter"
::= { x25CircuitEntry 11 }
x25CircuitOutPdus OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of PDUs sent for this circuit."
REFERENCE "10733 5.11 dataPacketsSent"
::= { x25CircuitEntry 12 }
x25CircuitOutInterrupts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of interrupt packets sent on
D. Throop Invalid after Dec 20, 92 [Page 46]
Internet Draft X.25 Packet Layer MIB June 1992
this circuit."
REFERENCE "10733 interruptPacketsSent"
::= { x25CircuitEntry 13 }
-- X25 circuit timer statistics
x25CircuitDataRetransmissionTimeouts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of times the T25 data
retransmission timer expired for this
circuit."
REFERENCE "10733 5.11 dataRetransmissionTimerExpiries"
::= { x25CircuitEntry 14 }
x25CircuitResetTimeouts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of times the T22 reset timer
expired for this circuit."
REFERENCE "10733 5.11 resetTimeouts"
::= { x25CircuitEntry 15 }
x25CircuitInterruptTimeouts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of times the T26 Interrupt timer
expired for this circuit."
REFERENCE "10733 interruptTimerExpiries"
::= { x25CircuitEntry 16 }
x25CircuitCallParamId OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This identifies the instance of the
x25CallParmIndex for the entry in the
D. Throop Invalid after Dec 20, 92 [Page 47]
Internet Draft X.25 Packet Layer MIB June 1992
x25CallParmTable which contains the call
parameters in use with this circuit. The
entry referenced must contain the values
that are currently in use by the circuit
rather than proposed values. A value of
NULL indicates the circuit is a PVC or is
using all the default parameters."
DEFVAL { {0 0} }
::= { x25CircuitEntry 17 }
x25CircuitCalledDteAddress OBJECT-TYPE
SYNTAX X121Address
ACCESS read-write
STATUS mandatory
DESCRIPTION
"For incoming calls, this is the called
address from the call indication packet.
For outgoing calls, this is the called
address from the call confirmation packet.
This will be zero length for PVCs."
REFERENCE "10733 calledDTEAddress"
DEFVAL { ''h }
::= { x25CircuitEntry 18 }
x25CircuitCallingDteAddress OBJECT-TYPE
SYNTAX X121Address
ACCESS read-write
STATUS mandatory
DESCRIPTION
"For incoming calls, this is the calling
address from the call indication packet.
For outgoing calls, this is the calling
address from the call confirmation packet.
This will be zero length for PVCs."
REFERENCE "10733 callingDTEAddress"
DEFVAL { ''h }
::= { x25CircuitEntry 19 }
x25CircuitOriginallyCalledAddress OBJECT-TYPE
SYNTAX X121Address
ACCESS read-write
STATUS mandatory
DESCRIPTION
"For incoming calls, this is the address in
the call Redirection or Call Deflection
D. Throop Invalid after Dec 20, 92 [Page 48]
Internet Draft X.25 Packet Layer MIB June 1992
Notification facility if the call was
deflected or redirected, otherwise it will
be called address from the call indication
packet. For outgoing calls, this is the
address from the call request packet. This
will be zero length for PVCs."
REFERENCE "10733 originallyCalledAddress"
DEFVAL { ''h }
::= { x25CircuitEntry 20 }
x25CircuitDescr OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..255))
ACCESS read-write
STATUS mandatory
DESCRIPTION
"A descriptive string associated with this
circuit. This provides a place for the
agent to supply any descriptive information
it knows about the use or owner of the
circuit. The agent may return the process
identifier and user name for the process
using the circuit. Alternative the agent
may return the name of the configuration
entry that caused a bridge to establish the
circuit. A zero length value indicates the
agent doesn't have any additional
information."
DEFVAL { ''h }
::= { x25CircuitEntry 21 }
-- ###########################################################
-- The Cleared Circuit Table
-- ###########################################################
x25ClearedCircuitEntriesRequested OBJECT-TYPE
SYNTAX PositiveInteger
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The requested number of entries for the
agent to keep in the x25ClearedCircuit
table."
::= { x25 6 }
D. Throop Invalid after Dec 20, 92 [Page 49]
Internet Draft X.25 Packet Layer MIB June 1992
x25ClearedCircuitEntriesGranted OBJECT-TYPE
SYNTAX PositiveInteger
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The actual number of entries the agent will
keep in the x25ClearedCircuit Table."
::= { x25 7 }
x25ClearedCircuitTable OBJECT-TYPE
SYNTAX SEQUENCE OF X25ClearedCircuitEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A table of entries about closed circuits.
Entries must be made in this table whenever
circuits are closed and the close request or
close indication packet contains a clearing
cause other than DTE Originated or a
Diagnostic code field other than Higher
Layer Initiated disconnection-normal. An
agent may optionally make entries for normal
closes (to record closing facilities or
other information).
Agents will delete the oldest entry in the
table when adding a new entry would exceed
agent resources. Agents are required to
keep the last entry put in the table and may
keep more entries. The object
x25OperClearEntriesGranted returns the
maximum number of entries kept in the
table."
REFERENCE "See ISO 8208 Section 12.2.3.1.1
and 12.2.3.1.2"
::= { x25 8 }
x25ClearedCircuitEntry OBJECT-TYPE
SYNTAX X25ClearedCircuitEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Information about a cleared circuit."
INDEX { x25ClearedCircuitIndex }
::= { x25ClearedCircuitTable 1 }
D. Throop Invalid after Dec 20, 92 [Page 50]
Internet Draft X.25 Packet Layer MIB June 1992
X25ClearedCircuitEntry ::= SEQUENCE {
x25ClearedCircuitIndex
PositiveInteger,
x25ClearedCircuitPleIndex
PositiveInteger,
x25ClearedCircuitTimeEstablished
TimeTicks,
x25ClearedCircuitTimeCleared
TimeTicks,
x25ClearedCircuitChannel
INTEGER,
x25ClearedCircuitClearingCause
INTEGER,
x25ClearedCircuitDiagnosticCode
INTEGER,
x25ClearedCircuitInPdus
Counter,
x25ClearedCircuitOutPdus
Counter,
x25ClearedCircuitCalledAddress
X121Address,
x25ClearedCircuitCallingAddress
X121Address,
x25ClearedCircuitClearFacilities
OCTET STRING
}
x25ClearedCircuitIndex OBJECT-TYPE
SYNTAX PositiveInteger
ACCESS read-only
STATUS mandatory
DESCRIPTION
"An index that uniquely distinguishes one
entry in the clearedCircuitTable from
another. This index will start at
2147483647 and will decrease by one for each
new entry added to the table. Upon reaching
one, the index will reset to 2147483647.
Because the index starts at 2147483647 and
decreases, a manager may do a getnext on
entry zero and obtain the most recent entry.
When the index has the value of 1, the next
entry will delete all entries in the table
and that entry will be numbered 2147483647."
::= { x25ClearedCircuitEntry 1 }
D. Throop Invalid after Dec 20, 92 [Page 51]
Internet Draft X.25 Packet Layer MIB June 1992
x25ClearedCircuitPleIndex OBJECT-TYPE
SYNTAX PositiveInteger
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The value of the x25AdmnIndex for the PLE
which cleared the circuit that created the
entry. The values of this object can range
from one to ifNumber."
::= { x25ClearedCircuitEntry 2 }
x25ClearedCircuitTimeEstablished OBJECT-TYPE
SYNTAX TimeTicks
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The value of sysUpTime when the circuit was
established. This will be the same value
that was in the x25CircuitEstablishTime for
the circuit."
::= { x25ClearedCircuitEntry 3 }
x25ClearedCircuitTimeCleared OBJECT-TYPE
SYNTAX TimeTicks
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The value of sysUpTime when the circuit was
cleared. For locally initiated clears, this
will be the time when the clear confirmation
was received. For remotely initiated
clears, this will be the time when the clear
indication was received."
::= { x25ClearedCircuitEntry 4 }
x25ClearedCircuitChannel OBJECT-TYPE
SYNTAX INTEGER (1..4096)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The channel number for the circuit that was
cleared."
::= { x25ClearedCircuitEntry 5 }
x25ClearedCircuitClearingCause OBJECT-TYPE
D. Throop Invalid after Dec 20, 92 [Page 52]
Internet Draft X.25 Packet Layer MIB June 1992
SYNTAX INTEGER (0..255)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The Clearing Cause from the clear request
or clear indication packet that cleared the
circuit."
REFERENCE "See ISO 8208 Section 12.2.3.1.1"
::= { x25ClearedCircuitEntry 6 }
x25ClearedCircuitDiagnosticCode OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The Diagnostic Code from the clear request
or clear indication packet that cleared the
circuit."
REFERENCE "See ISO 8208 Section 12.2.3.1.2"
::= { x25ClearedCircuitEntry 7 }
x25ClearedCircuitInPdus OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of PDUs received on the
circuit."
::= { x25ClearedCircuitEntry 8 }
x25ClearedCircuitOutPdus OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of PDUs transmitted on the
circuit."
::= { x25ClearedCircuitEntry 9 }
x25ClearedCircuitCalledAddress OBJECT-TYPE
SYNTAX X121Address
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The called address from the cleared
D. Throop Invalid after Dec 20, 92 [Page 53]
Internet Draft X.25 Packet Layer MIB June 1992
circuit."
::= { x25ClearedCircuitEntry 10 }
x25ClearedCircuitCallingAddress OBJECT-TYPE
SYNTAX X121Address
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The calling address from the cleared
circuit."
::= { x25ClearedCircuitEntry 11 }
x25ClearedCircuitClearFacilities OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0..109))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The facilities field from the clear request
or clear indication packet that cleared the
circuit. A size of zero indicates no
facilities were present."
::= { x25ClearedCircuitEntry 12 }
-- ###########################################################
-- The Call Parameter Table
-- ###########################################################
x25CallParmTable OBJECT-TYPE
SYNTAX SEQUENCE OF X25CallParmEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"These objects contain the parameters that
can be varied between X.25 calls. The
entries in this table are independent of the
PLE. There exists only one of these tables
for the entire system. The indexes for the
entries are independent of any PLE or any
circuit. Other tables reference entries in
this table. Entries in this table can be
used for default PLE parameters, for
parameters to use to place/answer a call,
D. Throop Invalid after Dec 20, 92 [Page 54]
Internet Draft X.25 Packet Layer MIB June 1992
for the parameters currently in use for a
circuit, or parameters that were used by a
circuit."
::= { x25 9 }
x25CallParmEntry OBJECT-TYPE
SYNTAX X25CallParmEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Entries of x25CallParmTable."
INDEX { x25CallParmIndex }
::= { x25CallParmTable 1 }
X25CallParmEntry ::= SEQUENCE {
x25CallParmIndex
PositiveInteger,
x25CallParmStatus
EntryStatus,
x25CallParmInPacketSize
INTEGER,
x25CallParmOutPacketSize
INTEGER,
x25CallParmInWindowSize
INTEGER,
x25CallParmOutWindowSize
INTEGER,
x25CallParmAcceptReverseCharging
INTEGER,
x25CallParmProposeReverseCharging
INTEGER,
x25CallParmFastSelect
INTEGER,
x25CallParmInThruPutClasSize
INTEGER,
x25CallParmOutThruPutClasSize
INTEGER,
x25CallParmCug
DisplayString,
x25CallParmCugoa
DisplayString,
x25CallParmBcug
DisplayString,
x25CallParmNui
OCTET STRING,
D. Throop Invalid after Dec 20, 92 [Page 55]
Internet Draft X.25 Packet Layer MIB June 1992
x25CallParmChargingInfo
INTEGER,
x25CallParmRpoa
DisplayString,
x25CallParmTrnstDly
INTEGER,
x25CallParmCallingExt
DisplayString,
x25CallParmCalledExt
DisplayString,
x25CallParmInMinThuPutCls
INTEGER,
x25CallParmOutMinThuPutCls
INTEGER,
x25CallParmEndTrnsDly
OCTET STRING,
x25CallParmPriority
OCTET STRING,
x25CallParmProtection
DisplayString,
x25CallParmExptData
INTEGER,
x25CallParmUserData
OCTET STRING,
x25CallParmCallingNetworkFacilities
OCTET STRING,
x25CallParmCalledNetworkFacilities
OCTET STRING
}
x25CallParmIndex OBJECT-TYPE
SYNTAX PositiveInteger
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A value that distinguishes this entry from
another entry. Entries in this table are
referenced from other objects which identify
call parameters.
It is impossible to know what other objects
in the MIB reference entries in the table by
looking at this table. Because of this,
changes to parameters must be accomplished
by creating a new entry in this table and
D. Throop Invalid after Dec 20, 92 [Page 56]
Internet Draft X.25 Packet Layer MIB June 1992
then changing the referencing table to
identify the new entry.
Since changes will only be effected by
setting an index in an object in another
table, an agent is only expected to make
changes take effect when other tables are
changed. Further managers should not assume
that since they set a index of this table
into an another object that the other object
will have the value of that index. Agents
are free to implement the set by copying
parameters rather than changing indexes.
Entries in this table that are not
referenced by any other object in the MIB
maybe deleted at the convence of the agent.
Care should be taken by the agent to give
the NMS sufficient time to create a
reference to newly created entries.
Should a Management Station not find a free
index with which to create a new entry, it
may feel free to delete entries. Agent must
either refuse to delete entries in use or
have provisions for recreating entries as
needed."
::= { x25CallParmEntry 1 }
x25CallParmStatus OBJECT-TYPE
SYNTAX EntryStatus
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The status of this call parameter entry.
See RFC 1271 for details of usage."
::= { x25CallParmEntry 2 }
x25CallParmInPacketSize OBJECT-TYPE
SYNTAX INTEGER (0..4096)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The maximum receive packet size in octets
for a circuit. A size of zero for a circuit
D. Throop Invalid after Dec 20, 92 [Page 57]
Internet Draft X.25 Packet Layer MIB June 1992
means use the PLE default size. A size of
zero for the PLE means use a default size of
128."
REFERENCE "10733 proposedPacketSize;
See ISO 8208 Section 15.2.2.1.1"
DEFVAL { 128 }
::= { x25CallParmEntry 3 }
x25CallParmOutPacketSize OBJECT-TYPE
SYNTAX INTEGER (0..4096)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The maximum transmit packet size in octets
for a circuit. A size of zero for a circuit
means use the PLE default size. A size of
zero for the PLE default means use a default
size of 128."
REFERENCE "10733 proposedPacketSize;
See ISO 8208 Section 15.2.2.1.1"
DEFVAL { 128 }
::= { x25CallParmEntry 4 }
x25CallParmInWindowSize OBJECT-TYPE
SYNTAX INTEGER (0..127)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The receive window size for a circuit. A
size of zero for a circuit means use the PLE
default size. A size of zero for the PLE
default means use 2."
REFERENCE "10733 proposedWindowSize;
See ISO 8208 Section 15.2.2.1.2"
DEFVAL { 2 }
::= { x25CallParmEntry 5 }
x25CallParmOutWindowSize OBJECT-TYPE
SYNTAX INTEGER (0..127)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The transmit window size for a circuit. A
size of zero for a circuit means use the PLE
default size. A size of zero for the PLE
D. Throop Invalid after Dec 20, 92 [Page 58]
Internet Draft X.25 Packet Layer MIB June 1992
default means use 2."
REFERENCE "10733 proposedWindowSize;
See ISO 8208 Section 15.2.2.1.2"
DEFVAL { 2 }
::= { x25CallParmEntry 6 }
x25CallParmAcceptReverseCharging OBJECT-TYPE
SYNTAX INTEGER {
default (1),
accept (2),
refuse (3),
neverAccept (4)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"An enumeration defining if the PLE will
accept or refuse charges. A value of
default for a circuit means use the PLE
default value. A value of neverAccept is
only used for the PLE default and indicates
the PLE will never accept reverse charging.
A value of default for a PLE default means
refuse."
REFERENCE "10733 acceptReverseCharging"
DEFVAL { refuse }
::= { x25CallParmEntry 7 }
x25CallParmProposeReverseCharging OBJECT-TYPE
SYNTAX INTEGER {
default (1),
reverse (2),
local (3)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"An enumeration defining if the PLE should
propose reverse or local charging. The
value of default for a circuit means use the
PLE default. The value of default for the
PLE default means use local."
REFERENCE "10733 proposedPacketSize;
See ISO 8208 Section 15.2.2.6"
DEFVAL { local }
D. Throop Invalid after Dec 20, 92 [Page 59]
Internet Draft X.25 Packet Layer MIB June 1992
::= { x25CallParmEntry 8 }
x25CallParmFastSelect OBJECT-TYPE
SYNTAX INTEGER {
default (1),
notSpecified (2),
fastSelect (3),
restrictedFastResponse (4),
noFastSelect (5),
noRestrictedFastResponse (6)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Expresses preference for use of fast select
facility. The value of default for a
circuit is the PLE default. A value of
default for the PLE means noFastSelect. A
value of noFastSelect or
noRestrictedFastResponse indicates a circuit
may not use fast select or restricted fast
response."
REFERENCE "10733 fastSelect;
Sec ISO 8208 Section 15.2.2.6"
DEFVAL { noFastSelect }
::= { x25CallParmEntry 9 }
x25CallParmInThruPutClasSize OBJECT-TYPE
SYNTAX INTEGER {
tcReserved1 (1),
tcReserved2 (2),
tc75 (3),
tc150 (4),
tc300 (5),
tc600 (6),
tc1200 (7),
tc2400 (8),
tc4800 (9),
tc9600 (10),
tc19200 (11),
tc48000 (12),
tc64000 (13),
tcReserved14 (14),
tcReserved15 (15),
tcReserved0 (16),
D. Throop Invalid after Dec 20, 92 [Page 60]
Internet Draft X.25 Packet Layer MIB June 1992
tcNone (17),
tcDefault (18)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The incoming throughput class to negotiate.
A value of tcDefault for a circuit means use
the PLE default. A value of tcDefault for
the PLE default means tcNone. A value of
tcNone means do not negotiate throughtput
class."
REFERENCE "See ISO 8208 Section 15.2.2.2, table 18"
DEFVAL { tcNone }
::= { x25CallParmEntry 10 }
x25CallParmOutThruPutClasSize OBJECT-TYPE
SYNTAX INTEGER {
tcReserved1 (1),
tcReserved2 (2),
tc75 (3),
tc150 (4),
tc300 (5),
tc600 (6),
tc1200 (7),
tc2400 (8),
tc4800 (9),
tc9600 (10),
tc19200 (11),
tc48000 (12),
tc64000 (13),
tcReserved14 (14),
tcReserved15 (15),
tcReserved0 (16),
tcNone (17),
tcDefault (18)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The outgoing throughput class to negotiate.
A value of tcDefault for a circuit means use
the PLE default. A value of tcDefault for
the PLE default means use tcNone. A value
of tcNone means do not negotiate throughtput
D. Throop Invalid after Dec 20, 92 [Page 61]
Internet Draft X.25 Packet Layer MIB June 1992
class."
REFERENCE "See ISO 8208 Section 15.2.2.2, table 18"
DEFVAL { tcNone }
::= { x25CallParmEntry 11 }
x25CallParmCug OBJECT-TYPE
SYNTAX DisplayString (SIZE(0..4))
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The Closed User Group to specify. This
consists of two or four octets containing
the characters 0 through 9. A zero length
string indicates no facility requested. A
string length of three containing the
characters DEF for a circuit means use the
PLE default, (the PLE default parameter may
not reference an entry of DEF.)"
REFERENCE "See ISO 8208 Section 15.2.2.3"
DEFVAL { ''h }
::= { x25CallParmEntry 12 }
x25CallParmCugoa OBJECT-TYPE
SYNTAX DisplayString (SIZE(0..4))
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The Closed User Group with Outgoing Access
to specify. This consists of two or four
octets containing the characters 0 through
9. A string length of three containing the
characters DEF for a circuit means use the
PLE default (the PLE default parameters may
not reference an entry of DEF). A zero
length string indicates no facility
requested."
REFERENCE "See ISO 8208 Section 15.2.2.4"
DEFVAL { ''h }
::= { x25CallParmEntry 13 }
x25CallParmBcug OBJECT-TYPE
SYNTAX DisplayString (SIZE(0..3))
ACCESS read-write
STATUS mandatory
DESCRIPTION
D. Throop Invalid after Dec 20, 92 [Page 62]
Internet Draft X.25 Packet Layer MIB June 1992
"The Bilateral Closed User Group to specify.
This consists of two octets containing the
characters 0 through 9. A string length of
three containing the characters DEF for a
circuit means use the PLE default (the PLE
default parameter may not reference an entry
of DEF). A zero length string indicates no
facility requested."
REFERENCE "See ISO 8208 Section 15.2.2.5"
DEFVAL { ''h }
::= { x25CallParmEntry 14 }
x25CallParmNui OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(0..108))
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The Network User Identifier facility. This
is binary value to be included immediately
after the length field. The PLE will supply
the length octet. A zero length string
indicates no facility requested. This value
is ignored for the PLE default parameters
entry."
REFERENCE "See ISO 8208 Section 15.2.2.7"
DEFVAL { ''h }
::= { x25CallParmEntry 15 }
x25CallParmChargingInfo OBJECT-TYPE
SYNTAX INTEGER {
default (1),
noFacility (2),
noChargingInfo (3),
chargingInfo (4)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The charging Information facility. A value
of default for a circuit means use the PLE
default. The value of default for the
default PLE parameters means use noFacility.
The value of noFacility means do not include
a facility."
REFERENCE "See ISO 8208 Section 15.2.2.8"
D. Throop Invalid after Dec 20, 92 [Page 63]
Internet Draft X.25 Packet Layer MIB June 1992
DEFVAL { noFacility }
::= { x25CallParmEntry 16 }
x25CallParmRpoa OBJECT-TYPE
SYNTAX DisplayString (SIZE(0..108))
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The RPOA facility. The octet string
contains n * 4 sequences of the characters
0-9 to specify a facility with n entries.
The octet string containing the 3 characters
DEF for a circuit specifies use of the PLE
default (the entry for the PLE default may
not contain DEF). A zero length string
indicates no facility requested."
REFERENCE "See ISO 8208, section 15.2.2.9"
DEFVAL { ''h }
::= { x25CallParmEntry 17 }
x25CallParmTrnstDly OBJECT-TYPE
SYNTAX INTEGER (0..65537)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The Transit Delay Selection and Indication
value. A value of 65536 indicates no
facility requested. A value of 65537 for a
circuit means use the PLE default (the PLE
default parameters entry may not use the
value 65537). The value 65535 may only be
used to indicate the value in use by a
circuit."
REFERENCE "See ISO 8208, Section 15.2.2.13"
DEFVAL { 65536 }
::= { x25CallParmEntry 18 }
-- The following parameters are for CCITT facilities.
x25CallParmCallingExt OBJECT-TYPE
SYNTAX DisplayString (SIZE(0..40))
ACCESS read-write
STATUS mandatory
DESCRIPTION
D. Throop Invalid after Dec 20, 92 [Page 64]
Internet Draft X.25 Packet Layer MIB June 1992
"The Calling Extension facility. This
contains one of the following:
A sequence of hex digits with the value to
be put in the facilty. These digits will be
converted to binary by the agent and put in
the facility. These octets do not include
the length octet.
A value containing the three character DEF
for a circuit means use the PLE default,
(the entry for the PLE default parameters
may not use the value DEF).
A zero length string indicates no facility
requested."
REFERENCE "See ISO 8208 Section 15.3.2.1"
DEFVAL { ''h }
::= { x25CallParmEntry 19 }
x25CallParmCalledExt OBJECT-TYPE
SYNTAX DisplayString (SIZE(0..40))
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The Called Extension facility. This
contains one of the following:
A sequence of hex digits with the value to
be put in the facilty. These digits will be
converted to binary by the agent and put in
the facility. These octets do not include
the length octet.
A value containing the three character DEF
for a circuit means use the PLE default,
(the entry for the PLE default parameters
may not use the value DEF).
A zero length string indicates no facility
requested."
REFERENCE "See ISO 8208 Section 15.3.2.2"
DEFVAL { ''h }
::= { x25CallParmEntry 20 }
D. Throop Invalid after Dec 20, 92 [Page 65]
Internet Draft X.25 Packet Layer MIB June 1992
x25CallParmInMinThuPutCls OBJECT-TYPE
SYNTAX INTEGER (0..17)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The minimum input throughput Class. A
value of 16 for a circuit means use the PLE
default (the PLE parameters entry may not
use this value). A value of 17 indicates no
facility requested."
REFERENCE "See ISO 8208 Section 15.3.2.3"
DEFVAL { 17 }
::= { x25CallParmEntry 21 }
x25CallParmOutMinThuPutCls OBJECT-TYPE
SYNTAX INTEGER (0..17)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The minimum output throughput Class. A
value of 16 for a circuit means use the PLE
default (the PLE parameters entry may not
use this value). A value of 17 indicates no
facility requested."
REFERENCE "See ISO 8208 Section 15.3.2.3"
DEFVAL { 17 }
::= { x25CallParmEntry 22 }
x25CallParmEndTrnsDly OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(0..6))
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The End-to-End Transit Delay to negotiate.
An octet string of length 2, 4, or 6
contains the facility encoded as specified
in ISO/IEC 8208 section 15.3.2.4. An octet
string of length 3 containing the three
character DEF for a circuit means use the
PLE default (the entry for the PLE default
can not contain the characters DEF). A zero
length string indicates no facility
requested."
REFERENCE "See ISO 8208 Section 15.3.2.4"
DEFVAL { ''h }
D. Throop Invalid after Dec 20, 92 [Page 66]
Internet Draft X.25 Packet Layer MIB June 1992
::= { x25CallParmEntry 23 }
x25CallParmPriority OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(0..6))
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The priority facility to negotiate. The
octet string encoded as specified in ISO/IEC
8208 section 15.3.2.5. A zero length string
indicates no facility requested. The entry
for the PLE default parameters must be zero
length."
REFERENCE "See ISO 8208 Section 15.3.2.5"
DEFVAL { ''h }
::= { x25CallParmEntry 24 }
x25CallParmProtection OBJECT-TYPE
SYNTAX DisplayString (SIZE(0..108))
ACCESS read-write
STATUS mandatory
DESCRIPTION
"A string contains the following:
A hex string containing the value for the
protection facility. This will be converted
from hex to the octets actually in the
packet by the agent. The agent will supply
the length field and the length octet is not
contained in this string.
An string containing the 3 characters DEF
for a circuit means use the PLE default (the
entry for the PLE default parameters may not
use the value DEF).
A zero length string mean no facility
requested."
REFERENCE "See ISO 8208 Section 15.3.2.5"
DEFVAL { ''h }
::= { x25CallParmEntry 25 }
x25CallParmExptData OBJECT-TYPE
SYNTAX INTEGER {
default (1),
D. Throop Invalid after Dec 20, 92 [Page 67]
Internet Draft X.25 Packet Layer MIB June 1992
noExpeditedData (2),
expeditedData (3)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The Expedited Data facility to negotiate.
A value of default for a circuit means use
the PLE default value. The entry for the
PLE default parameters may not have the
value default."
REFERENCE "See ISO 8208 Section 15.3.2.7"
DEFVAL { noExpeditedData }
::= { x25CallParmEntry 26 }
x25CallParmUserData OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0..128))
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The call user data as placed in the packet.
A zero length string indicates no call user
data. If both the circuit call parameters
and the PLE default have call user data
defined, the data from the circuit call
parameters will be used. If only the PLE
has data defined, the PLE entry will be
used. If neither the circuit call
parameters or the PLE default entry has a
value, no call user data will be sent."
REFERENCE "See ISO 8208 Section 12.2.1.1.6, 12.2.1.2"
DEFVAL { ''h }
::= { x25CallParmEntry 27 }
x25CallParmCallingNetworkFacilities OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0..108))
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The calling network facilities. The
facilities are encoded here exactly as
encoded in the call packet. These
facilities do not include the marker
facility code.
D. Throop Invalid after Dec 20, 92 [Page 68]
Internet Draft X.25 Packet Layer MIB June 1992
A zero length string in the entry for the
parameter to use when establishing a circuit
means use the PLE default. A zero length
string in the entry for PLE default
parameters indicates no default facilities."
REFERENCE "See ISO 8206 Section 15.1, category b"
DEFVAL { ''h }
::= { x25CallParmEntry 28 }
x25CallParmCalledNetworkFacilities OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0..108))
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The called network facilities. The
facilities are encoded here exactly as
encoded in the call packet. These
facilities do not include the marker
facility code.
A zero length string in the entry for the
parameter to use when establishing a circuit
means use the PLE default. A zero length
string in the entry for PLE default
parameters indicates no default facilities."
REFERENCE "See ISO 8206 Section 15.1, category c"
DEFVAL { ''h }
::= { x25CallParmEntry 29 }
-- ###########################################################
-- X.25 Traps
-- ###########################################################
x25Restart TRAP-TYPE
ENTERPRISE x25
VARIABLES { x25OperIndex }
DESCRIPTION
"This trap means the X.25 PLE sent or
received a restart packet. The restart that
brings up the link should not send a
x25Restart trap so the interface should send
a linkUp trap. Sending this trap means the
agent does not send a linkDown and linkUp
trap."
::= 1
D. Throop Invalid after Dec 20, 92 [Page 69]
Internet Draft X.25 Packet Layer MIB June 1992
x25Reset TRAP-TYPE
ENTERPRISE x25
VARIABLES { x25CircuitIndex,
x25CircuitChannel }
DESCRIPTION
"If the PLE sends or receives a reset, the
agent should send an x25Reset trap."
::= 2
-- ###########################################################
-- X.25 Protocol Version Identifiers
-- ###########################################################
x25ProtocolVersion OBJECT IDENTIFIER
::= { x25 10 }
-- X.25 CCITT 1976 version.
x25protocolCcittV1976 OBJECT IDENTIFIER
::= { x25ProtocolVersion 1 }
-- X.25 CCITT 1980 version.
x25protocolCcittV1980 OBJECT IDENTIFIER
::= { x25ProtocolVersion 2 }
-- X.25 CCITT 1984 version.
x25protocolCcittV1984 OBJECT IDENTIFIER
::= { x25ProtocolVersion 3 }
-- X.25 CCITT 1988 version.
x25protocolCcittV1988 OBJECT IDENTIFIER
::= { x25ProtocolVersion 4 }
-- X.25 1987 version of ISO 8208.
x25protocolIso8208V1987 OBJECT IDENTIFIER
::= { x25ProtocolVersion 5 }
-- X.25 1989 version of ISO 8208.
x25protocolIso8208V1989 OBJECT IDENTIFIER
::= { x25ProtocolVersion 6 }
-- ###########################################################
END
D. Throop Invalid after Dec 20, 92 [Page 70]
Internet Draft X.25 Packet Layer MIB June 1992
7. Acknowledgements
This document was produced by the x25mib working group:
Fred Baker, ACC
Art Berggreen, ACC
Frank Bieser
Gary Bjerke, Tandem
Bill Bowman, HP
Christopher Bucci, Datability
Charles Carvalho, ACC
Jeff Case, Snmp Research
Angela Chen, HP
Carson Cheung, BNR
Tom Daniel, Spider Systems
Chuck Davin, MIT
Billy Durham, Honeywell
Richard Fox, Synoptics
Doug Geller, Data General
Herve Goguely, LIR Corp
Andy Goldthorpe, british-telecom
Walter D. Guilarte
David Gurevich
Steve Huston, Process Software Corporation
Jon Infante, ICL
Frank Kastenholz, Clearpoint
Zbigniew Kielczewski, Eicon
Cheryl Krupezak, Georgia Tech
Mats Lindstrom, Diab Data AB
Andrew Malis, BBN
Evan McGinnis, 3Com
Gary (G.P.)Mussar, BNR
Chandy Nilakantan, 3Com
Randy Pafford, Data General
Ragnar Paulson, The Software Group Limited
Dave Perkins, Synoptics
Walter Pinkarschewsky, DEC
Karen Quidley, Data General
Chris Ranch, Novell
Paul S. Rarey, DHL Systems Inc.
Jim Roche, Newbridge Research
Philippe Roger, LIR Corp.
Timon Sloane
Mike Shand, DEC
Brad Steina, Microcom
D. Throop Invalid after Dec 20, 92 [Page 71]
Internet Draft X.25 Packet Layer MIB June 1992
Bob Stewart, Xyplex
Tom Sullivan, Data General
Rodney Thayer, Sable Technology Corporation
Mark Therieau, Microcom
Jane Thorn, Data General
Dean Throop, Data General
Maurice Turcotte, Racal Datacom
Mike Zendels, Data General
In addition, the contributions of the following individuals
are also acknowledged:
John Harper, DEC
Chairman of the ISO committee for
Network Level Management Information
D. Throop Invalid after Dec 20, 92 [Page 72]
Internet Draft X.25 Packet Layer MIB June 1992
8. References
[1] M.T. Rose and K. McCloghrie, "Structure and
Identification of Management Information for TCP/IP-based
internets", RFC 1155, Network Information Center, SRI
International, Menlo Park, California, (May, 1990).
[2] K. McCloghrie and M.T. Rose, "Management Information Base
for Network Management of TCP/IP-based internets", RFC
1156, Network Information Center, SRI International,
Menlo Park, California, (May, 1990).
[3] J.D. Case, M.S. Fedor, M.L. Schoffstall, and J.R. Davin,
"Simple Network Management Protocol", RFC 1157, Network
Information Center, SRI International, Menlo Park,
California, (May, 1990).
[4] M.T. Rose, K. McCloghrie (editors), "Towards Concise MIB
Definitions", RFC 1212, Network Information Center, SRI
International, Menlo Park, California, (March, 1991)
[5] M.T. Rose (editor), "Management Information Base for
Network Management of TCP/IP-based internets", RFC 1213.
Network Information Center, SRI International, Menlo
Park, California, (March, 1991).
[6] "Information processing systems - Open Systems
Interconnection - Specification of Abstract Syntax
Notation One (ASN.1)", International Organization for
Standardization. International Standard 8824, (December,
1987).
[7] "Information processing systems - Open Systems
Interconnection - Specification of Basic Encoding Rules
for Abstract Notation One (ASN.1)", International
Organization for Standardization. International Standard
8825, (December, 1987).
[8] B. Stewart (editor), "Definitions of Managed Objects for
RS-232-like Hardware Devices", Internet Draft, Internet
Engineering Task Force, (December, 1990)
[9] D. Throop (editor), "SNMP MIB extension for LAPB",
Internet Draft, Internet Engineering Task Force,
(February, 1992)
D. Throop Invalid after Dec 20, 92 [Page 73]
Internet Draft X.25 Packet Layer MIB June 1992
[10] "Information technology - - Data communication - X.25
Packet layer Protocol for Data Terminal Equipment",
International Organization for Standardization,
International Standard 8208 (March, 1990)
[11] "Information Technology - Telecommunications and
information exchange between systems - Elements of
Management Information Related to OSI network Layer
Standards", Committee Draft International Standard 10733,
(November, 1990)
D. Throop Invalid after Dec 20, 92 [Page 74]
Internet Draft X.25 Packet Layer MIB June 1992
Table of Contents
1 Status of this Memo ................................... 1
1.1 Revision History .................................... 2
June 1992 .............................................. 2
April 1992 ............................................. 3
February 1992 .......................................... 4
October 1991 ........................................... 5
June 1991 .............................................. 5
April 1991 ............................................. 5
2 Abstract .............................................. 5
3 The Network Management Framework ...................... 6
4 Objects ............................................... 6
4.1 Format of Definitions ............................... 7
5 Overview .............................................. 8
5.1 Informal Overview ................................... 8
5.2 Textual Conventions ................................. 9
5.3 Structure of MIB .................................... 9
5.4 Tables .............................................. 10
5.5 Table Usage ......................................... 11
5.6 Conformance ......................................... 12
6 Object Definitions .................................... 13
7 Acknowledgements ...................................... 71
8 References ............................................ 73
D. Throop Invalid after Dec 20, 92 [Page 75]
Dean Throop throop@dg-rtp.dg.com
- X25MIB Part II Dean D. Throop