[netmod] [Errata Rejected] RFC8519 (5762)

RFC Errata System <rfc-editor@rfc-editor.org> Tue, 24 September 2019 06:37 UTC

To: bill.wu@huawei.com, mjethanandani@gmail.com, sagarwal12@gmail.com, huangyi_99@yahoo.com, dana@blairhome.com
From: RFC Errata System <rfc-editor@rfc-editor.org>
Cc: joelja@bogus.com, iesg@ietf.org, netmod@ietf.org, rfc-editor@rfc-editor.org
Content-Type: text/plain; charset="UTF-8"
Message-Id: <20190924063732.4D0D2B81253@rfc-editor.org>
Date: Mon, 23 Sep 2019 23:37:32 -0700
Archived-At: <https://mailarchive.ietf.org/arch/msg/netmod/XbteSGdfu0ywx09TyBWpsl9tZI8>
Subject: [netmod] [Errata Rejected] RFC8519 (5762)
Precedence: list

The following errata report has been rejected for RFC8519,
"YANG Data Model for Network Access Control Lists (ACLs)".

--------------------------------------
You may review the report below and at:
https://www.rfc-editor.org/errata/eid5762

--------------------------------------
Status: Rejected
Type: Technical

Reported by: Qin WU <bill.wu@huawei.com>
Date Reported: 2019-06-24
Rejected by: Joel Jaeggli (IESG)

Section: 4.1

Original Text
-------------
leaf type {
type acl-type;
description
"Type of ACL. Indicates the primary intended
type of match criteria (e.g., Ethernet,
IPv4, IPv6, mixed, etc.) used in the list
instance.";
}

Corrected Text
--------------
leaf type {
type acl-type;
default "ipv4-acl-type";
description
"Type of ACL. Indicates the primary intended
type of match criteria (e.g., Ethernet,
IPv4, IPv6, mixed, etc.) used in the list
instance.";
}

Notes
-----
I am wondering why not set default value for acl-type,e.g., set default value as "ipv4-acl-type" otherwise, how to determine which field under which choice will be matched upon and which action should be taken on them if the opetional parameter type under acl list is not set.

Also I want to better understand why acl type is removed from key indexes of access list and keep it as optional parameter under acl list. One case I am thinking in my mind is we add a mixed Ethernet, IPv4, and IPv6 ACL entry when we already have Ethernet ACL entry,IPv4 ACL entry , we don't need to remove existing ethernet entry and existing IPv4 entry in the list ("aces") and create a new entry with mixed ethernet, IPv4, IPv6 ACL, instead, we just add a new identity called mixed-eth-ipv4-ipv6-acl-type and add a new IPv6 entry.
--VERIFIER NOTES--

Mahesh Jethanandani replied:

This errata should be rejected for the following reason.

The whole idea of defining the identities for acl-type was to allow vendors to specify what capabilities their box is capable of supporting and then to specify what capabilities the vendors want to support. As such there is no “default capability" for every vendor. Besides, if a device advertises a mixed-eth-ipv4 feature, it is because it can only support Ethernet and IPv4 ACL combinations, and it cannot support IPv6 ACL matches. You do not add a capability of IPv6 match on the fly. It either has it, or it does not. If it does, advertise mixed-eth-ipv4-ipv6 capability to begin with.

The errata proposes a change to the standard and is not correcting an error in the document. additionaly it not clear why it would be appraise to set a default acl type.

The errata is declined.

--------------------------------------
RFC8519 (draft-ietf-netmod-acl-model-21)
--------------------------------------
Title : YANG Data Model for Network Access Control Lists (ACLs)
Publication Date : March 2019
Author(s) : M. Jethanandani, S. Agarwal, L. Huang, D. Blair
Category : PROPOSED STANDARD
Source : Network Modeling
Area : Operations and Management
Stream : IETF
Verifying Party : IESG

[netmod] [Errata Rejected] RFC8519 (5762) RFC Errata System