Re: [Netconf] I-D Action: draft-wu-netconf-restconf-factory-restore-00.txt

Hi Wuqin,

Some initial comments.

1.  I feel it is better if all the datastores used for source / target should be datastore-ref used from ietf-datastore module
2.  I think the factory-restore may be helpful for the ephemeral data-stores, if they want to revert the configurations (without a reboot).
3.  ietf-restconf-restore why is it a RESTCONF module... Why any other protocol cannot use it ?
4.  RPC names factory-recovery vs factory-restore , which is correct ?
5.  Section 1
 "especially when the RESTCONF server is implemented in a
   device that does not have NETCONF support."
   ==> Better to add that Section 8.7.5.1 of RFC 6241 provides a mechanism to reset to factory defaults. 
   Else users may not know why it is OK, if NETCONF is supported.

With Regards,
Rohit R Ranade

-----Original Message-----
From: Netconf [mailto:netconf-bounces@ietf.org] On Behalf Of Qin Wu
Sent: 28 June 2018 08:41
To: netconf@ietf.org
Subject: Re: [Netconf] I-D Action: draft-wu-netconf-restconf-factory-restore-00.txt

Hi, All:
We submit a new I-D to discuss "Factory default Setting Capability for RESTCONF"
https://tools.ietf.org/html/draft-wu-netconf-restconf-factory-restore-00
The abstract:
   This document defines capability based extension to RESTCONF protocol
   that allows RESTCONF client to configure newly deployed devices with
   just its preconfigured initial state (i.e., factory default settings)
   during zero touch bootstrapping process or restore the configuration
   to its preconfigured initial state or system restore point either
   during device rooting process or at the time of system fatal error or
   malfunction.
Your comments and suggestions are welcome.

-Qin
-----邮件原件-----
发件人: I-D-Announce [mailto:i-d-announce-bounces@ietf.org] 代表 internet-drafts@ietf.org
发送时间: 2018年6月27日 19:29
收件人: i-d-announce@ietf.org
主题: I-D Action: draft-wu-netconf-restconf-factory-restore-00.txt

A New Internet-Draft is available from the on-line Internet-Drafts directories.

        Title           : Factory default Setting Capability for RESTCONF
        Authors         : Qin Wu
                          Ye Niu
	Filename        : draft-wu-netconf-restconf-factory-restore-00.txt
	Pages           : 11
	Date            : 2018-06-27

Abstract:
   This document defines capability based extension to RESTCONF protocol
   that allows RESTCONF client to configure newly deployed devices with
   just its preconfigured initial state (i.e., factory default settings)
   during zero touch bootstrapping process or restore the configuration
   to its preconfigured initial state or system restore point either
   during device rooting process or at the time of system fatal error or
   malfunction.

The IETF datatracker status page for this draft is:
https://datatracker.ietf.org/doc/draft-wu-netconf-restconf-factory-restore/

There are also htmlized versions available at:
https://tools.ietf.org/html/draft-wu-netconf-restconf-factory-restore-00
https://datatracker.ietf.org/doc/html/draft-wu-netconf-restconf-factory-restore-00

Please note that it may take a couple of minutes from the time of submission until the htmlized version and diff are available at tools.ietf.org.

Internet-Drafts are also available by anonymous FTP at:
ftp://ftp.ietf.org/internet-drafts/

_______________________________________________
I-D-Announce mailing list
I-D-Announce@ietf.org
https://www.ietf.org/mailman/listinfo/i-d-announce
Internet-Draft directories: http://www.ietf.org/shadow.html or ftp://ftp.ietf.org/ietf/1shadow-sites.txt
_______________________________________________
Netconf mailing list
Netconf@ietf.org
https://www.ietf.org/mailman/listinfo/netconf